View IK642B_8343809.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

technical data 1 201 3 june , ver. 0 0 interval - and wipe/wash wiper control ic the IK642B is a bi - polar integrated circuit designed for the wiper application in the automotive market. it includes wipe, wash and internal mode. features ? interval pau se: 4 to 20 s ? after - wiping time: 2 to 20 s ? wiper motor's park switch ? wipe/wash mode priority ? one external capacitor determines all time sequences ? relay driver with z - diode ? load - dump protected ? prewash delay 300ms ? interference protection according to vde 0839 or iso/tr 7637/1 ordering information device operating temperature range package packing IK642Bn = - 40 to +85 ? dip8 tube IK642Bdt so8 tape & reel IK642Bd so8 tube functional description as a convenience featu re of the windshield wiper, intermittent and wipe/wash operation functions are implemented in most of the automobiles. the IK642B is a cost - effective solution for an accurate timing function control. wipe/wash mode has priority over interval mode. interval pause and after - wiping time can be set to fixed values by using resistors in a broad time range. added value can be provided with an individual, continuous adjustment of the interval pause by a potentiometer which may be built into the stalk. for proper o peration, it is mandatory to feed the signal of the wiper motor's park switch into IK642B . ik 642b so8 dip8
ik 642b 2 20 13 june , ver. 0 0 block diagram figure 1 pin configuration figure 2
ik 642b 3 20 13 june , ver. 0 0 pin description pin n o . symbol description 1 gnd ground 2 int interval switch 3 ct timing capa citor c2 4 rt after - wiping time resistance 5 wash wipe/wash switch 6 park park switch for wiper motor 7 out relay control output 8 vs supply voltage terminal 15
ik 642b 4 20 13 june , ver. 0 0 circuit description i nterval function, pin 2 by closing the interval switch, s 2 , to supply voltage, v batt , the relay is activated. the internal current source (pin 3) which holds the capacitor c 2 in a charged state is switched - off. as soon as there is a positive potential at the park switch (s1), the current source f (see figure 1 on pag e 1) charges the capacitor c2 very quickly. after the wiper operation is finished, s 1 is again at ground potential, the relay is in the off position - interval pause begins - the capacitor c 2 is discharged through the current source c, till the voltage at p in 3 is below the threshold of 2 v. interval pause can be adjusted between 4 s to 20 s with the help of potentiometer r 3 . now the relay switches on and the next interval cycle begins. opening of switch s 2 causes the current source a to discharge c 2 immedia tely and current sources c and f are switched - off. wipe/wash (wiwa) operation, pin 5 by closing the wiwa switch, s 3 , to supply voltage, v batt , the water pump starts spraying water on the windshield. during this function, the current source a is swit ched - off which keeps the capacitor c 2 in a discharged state. now the capacitor is charged through the current sources d and f. if (after a time interval of approximately 100 ms) the voltage at the capacitor is greater than 6.5 v, the relay is turned on as long as the switch wiwa is closed. the after - wiping time begins when the switch is open, the sources d and f are switched off and the source e is activated. source e discharges the capacitor until the voltage is less than 2.2 v. the relay is off and the wiper - motor is supplied via the park switch until the park position is reached. the after - wiping time is determined by the current source e which can be regulated with the external resistor r time . when the after - wiping time has elapsed, the source a discha rges the capacitor. the relay switch is independent of the park switch s 1 . interval and wiwa functions the interval function is interrupted immediately when the wipe/wash mode is activated. the current source a discharges the capacitor to a value of 2 v, afterwards, the normal wash function starts. interval wiping starts immediately when the after - wipe time is over. the switching delays are slightly shorter, because the capacitor is already charged to a value of 2 v. the wipe/wash function is not interrupted when the interval switch s 2 is activated. the interval function begins after the wiwa function has elapsed.
ik 642b 5 20 13 june , ver. 0 0 figure 3. application circuit with interval and wipe/wash operation
ik 642b 6 20 13 june , ver. 0 0 absolute maximum ratings parameters pin symbol value unit supply voltage t = 60 s, terminal 15 8 v batt 28 v supply current t = 2 ms t = 200 ms 8 i 8 i 8 1.5 150 a ma relay control output current (dc) t = 200 ms 7 i 7 i 7 200 1.2 ma a pulse current (control inputs) t = 200 ms park switch, s 1 wipe/wash switch , s 3 interval switch, s 2 6 5 2 i 6 i 5 i 2 50 50 50 ma power dissipation t amb = 90 c p tot 500 mw storage temperature range t stg - 55 to +125 c ambient temperature range t amb - 40 to +85 c thermal resistance parameter symbol value unit junction a mbient dip8 r thja 120 k/w so8 r thja 160 k/w stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions bey ond those indicated in the operational sections of this specification are not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ik 642b 7 20 13 june , ver. 0 0 electrical characteristics v batt = 12v, t amb = 25c, reference poi nt is pin 8 (see figure 3 on page 4) unless otherwise specified. parameter test conditions pin symbol min typ. max unit supply voltage 8 v batt 9 16.5 v supply current i 8 10 ma z - diode limitation v 1 7.6 v overvoltage threshold current i 1 - 50 ma threshold voltage v batt 35 v relay control output 7 saturation voltage i 7 = 100 ma i 7 = 200 ma v 7 - 1.0 - 1.5 v leakage current i 7 100 ua park switch 6 internal pull - up resistance r 6 = 10 k r 6 50 k? switching threshold voltage v 6 C 3.3 v protection diode i 6 = C 10 ma i 6 = 10 ma v 6 v 6 C 0.8 7.6 v input ct 3 internal resistance r 3 100 ? interval input r 2 = 2.7 to 30 k 2 protection diode i 2 = C 10 ma i 2 = 30 ma/10 ms v 2 C 0.8 7.6 v wash input r 5 = 10 k? 5 switching threshold/ hysteresis v 5 C 1.4/ C 5.4 v protection diode i 5 = C 10 ma i 5 = 10 ma v C 0.8 7.6 v switching characteristics r 4 = 47 k to 300 k?, i 4 = C 150 a interval time r 3 = 0 k? r 3 = 10 k? t 2 3.6 10.8 4 12 4.4 13.2 s prewash delay t del 3 00 ms after - wipe - time r 4 = 130 k? 5 t 5 4.75 5.25 5.75 s
ik 642b 8 20 13 june , ver. 0 0 diagrams figure 4. interval pause = f (t); c t = 22 f figure 5. after - wiping time = f (t); c t = 22 f; v batt = 8 v figure 6. interval pause = f (rint); c t = 22 f
ik 642b 9 20 13 june , ver. 0 0 figure 7. after - wiping time = f (t); c t = 22 f; v batt = 16 v
ik 642b 10 20 13 june , ver. 0 0 package dimension n suffix plastic dip (ms C 001ba) symbol min max a 8.51 10.16 b 6.1 7.11 c 5.33 d 0.36 0.56 f 1.14 1.78 g h j 0 10 k 2.92 3.81 notes: l 7.62 8.26 1. ???? dimensions a, b do not include mold flash or protrusions. m 0.2 0.36 maximum mold flash or protrusions 0.25?mm (0.010) per side. n 0.38 dimension, mm 2.54 7.62 l h m j a b f g d seating plane n k 0.25 (0.010) m t -t- c 1 8 4 5
ik 642b 11 20 13 june , ver. 0 0 n suffix plastic dip (ms C 001ba) symbol min max a 8.51 10.16 b 6.1 7.11 c 5.33 d 0.36 0.56 f 1.14 1.78 g h j 0 10 k 2.92 3.81 notes: l 7.62 8.26 1. ???? dimensions a, b do not include mold flash or protrusions. m 0.2 0.36 maximum mold flash or protrusions 0.25?mm (0.010) per side. n 0.38 d suffix soic (ms - 012aa) symbol min max a 4.8 5 b 3.8 4 c 1.35 1.75 d 0.33 0.51 f 0.4 1.27 g h j 0 8 notes: k 0.1 0.25 1. ???? dimensions a and b do not include mold flash or protrusion. m 0.19 0.25 2. ???? maximum mold flash or protrusion 0.15?mm (0.006) per side p 5.8 6.2 for a; for b ? 0.25?mm (0.010) per side. r 0.25 0.5 1.27 5.72 dimension, mm dimension, mm 2.54 7.62 l h m j a b f g d seating plane n k 0.25 (0.010) m t -t- c 1 8 4 5 a b h c k c m j f m p g d r x 45 seating plane 0.25 (0.010) m t -t- 1 8 4 5

▲Up To Search▲

Price & Availability of IK642B

	To Download IK642B Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .